Seiko LP-1030-MF Betriebsanweisung Seite 40
- Seite / 314
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
1-16
5
This button turns on/off the power supply to the device.
6
These LEDs indicate the statues of the device.
● [TONER] LED
Indicates the amount of remaining toner.
On: There is sufficient toner.
Flashing: Toner is running low.
Off: There is no toner (plots cannot be produced without
replacement.)
● [WASTE TONER] LED
Indicates the toner waste bottle status.
On: Normal
Flashing: Replacement time is approaching
Off: Plots cannot be produced without replacement
● [PROCESS] LED
Indicates the process cartridge replacement time.
On: Normal
Flashing: Replacement time is approaching
Off: Process cartridge is not installed.
● [MANUAL FEED] LED
This LED indicates whether the paper to be fed manually has been
loaded.
ON: Paper has been loaded.
OFF: No paper
● [1], [2] LEDs
These LEDs indicate whether the paper has been loaded in the roll 1
and roll 2 drawers, respectively.
ON: Paper has been loaded.
OFF: No paper
● [DATA] LED
This LED indicates the data receiving status.
ON: A job is waiting for the processing.
Flashing: Data is being received.
OFF: No received data
POWER
ERRORDATA
TONER
PROCESS
MANUAL FEED
WASTE
TONER
- LP-1020-MF 1
- LP-1020L-MF 1
- Introduction 5
- Safety Precautions 6
- Warning labels 9
- How to read this manual 11
- 1 Press [MENU] key to proceed 13
- 3 Press [ ] or [ ] and select 13
- Supplied components 14
- TABLE OF CONTENTS 15
- Chapter 3 Menu overview 3-1 17
- Chapter 13 Terioplot 13-1 22
- Appendix Appendix-1 23
- Getting started 25
- Features 26
- Operating conditions 28
- Installation space 30
- Supported 31
- Spool memory configuration 34
- Right side/rear side 36
- Interior 37
- Control panel 38
- ERRORDATA 40
- SCAN STOP 41
- Data standby display 42
- Data processing display 42
- Printing in progress display 43
- Print information display 43
- Setting ready display 43
- Error display 43
- Warming up display 44
- Basic operations 45
- Plotting procedures overview 46
- Turning the power on and off 47
- Main power switch 48
- Shu t down 50
- Installation operations 51
- ■Turning on the power 52
- ✽000 . 000 . 000.000 53
- ✽192.168. 123 . 123 53
- ✽192.168. 123 . 123 OK? 53
- Online and offline 54
- Replacing paper rolls 55
- How to detach the paper rolls 58
- 2 Move the flange guide 60
- 5 Cut the end of the paper 61
- Close the paper roll drawer 62
- Replacing the toner 63
- Precautions on handling 64
- 3 Close the scanner cover 66
- 4 Open the toner cover 67
- CLOSE LEVER 68
- REMOVE CARTR I DGE 68
- Return the lever to the left 69
- Wa s t e B o t t l e 70
- New bottle 72
- Bottle containing 72
- 6 Close the waste toner door 73
- Pr int Ready 74
- Process Car t r i dge 74
- 4 Remove the orange tape 77
- 7 Close the top door 78
- 8 Remove the filter cover 78
- 9 Replace the filter 79
- 1 Adjust the paper guide 80
- 1 Set the AUTO SUPPLY mode 81
- 2 Load the cut paper 81
- Chapter 2 Basic operations 83
- Example of A3 width cut paper 84
- Manual paper feed inlet 84
- Cut paper 84
- Print stop 85
- Continue printing 85
- Cancel printing 86
- Additional printing 86
- Web function 87
- 2 Launch the Web browser 88
- Cleaning the exterior 89
- Limiting rolls to be used 94
- Menu overview 95
- Channels and ports 96
- Data formats 97
- Reprinting 98
- Settings menu 99
- Menu name 100
- (Refer to “Note” below.) 101
- PDL menu 102
- Items which you can set 103
- Printing status 104
- Menu screen 105
- Device menu “DEVICE” 106
- Paper menu “PAPER” 107
- Function menu “FUNCTION” 108
- Protocol menu “PROTOCOL” 109
- Reset menu “RESET” 110
- System menu “SYSTEM” 111
- Basic Menu Operation 113
- Offline menu operation 115
- Moving the menu hierarchy 116
- ✽CONT MODE 117
- ✽OPT IMAL MODE 117
- ✽020 . 005 . 070 . 100 119
- ✽0 20 . 005 . 070 . 100 119
- ✽0 10 . 005 . 070 . 100 119
- ✽010 . 005 . 067 . 251 119
- ■Character input method 120
- ■Execution method 121
- ▼Offline menu operation 121
- ■Choice execution method 122
- Exiting the setting 123
- "SETUP" Menu 125
- Setting parameter items 126
- ▼Setting parameter items 127
- Setup parameter priority mode 134
- PARAMETER MODE (DSCAN only) 135
- AUTO SUPPLY 136
- FIXING MODE 137
- COPY COUNT 138
- SUPPLY PARAM 139
- DRAWING PARAM 141
- Error memo 144
- Paper feed 144
- Cut position 144
- SCALING PARAM 145
- ROUND BUTT 155
- MITERED length 156
- RASTER PARAM 158
- "DEVICE" menu 159
- Setting items 160
- POWER SAVE 161
- EDGE CUT TIMER 162
- DOOR OPEN CUT 163
- TRACIND PAPER MODE 163
- DOCSET TIME (sec) 164
- BOTTLE MAINT 164
- "PAPER" menu 165
- MEDIA SERIES 167
- "FUNCTION" menu 169
- MENU PRINT 171
- (Sample of print) 172
- HPGL SELF PLOT 173
- DSCAN SELF PLOT 174
- ERROR LOG 175
- Executes job log print 176
- ▼Setting items 177
- ENGINE LOG 178
- SCAN LOG 179
- SYSTEM DATE 180
- SYSTEM TIME 180
- INIT CHARG. INF 180
- PRINT CHARG. INF 180
- MAINTE INFO 181
- DATA DUMP 181
- "PROTOCOL" menu 183
- PDL SELECT 185
- XPT PORT 186
- PRINTER NAME 186
- USER NAME 187
- "RESET" menu 189
- Reset functions 190
- "SYSTEM" menu 191
- WEB LOCK 197
- ENABLE SERIES 198
- APPLY ROLL 200
- CHINA SIZE 202
- SCAN START 203
- MODE TIMEOUT 203
- COPY SETTING 203
- INITIAL SET 204
- LANGUAGE 205
- LENGTH UNITS 205
- ADMIN PASSWORD 205
- 1 Press the [ ] key 206
- 2 Press the [ ] or [ ] key 206
- 3 Press the [Enter] key 206
- Chapter 12 209
- PORT SELECT 212
- IP ADDRESS 213
- SUBNET MASK 213
- ROUTING TABLE 214
- SETUP DETAILS 215
- Terioplot 221
- Settings 224
- Restrictions 225
- Troubleshooting 227
- When an error message appears 229
- 1 Open the top door 230
- 2 Remove the jammed paper 230
- 4 Remove the jammed paper 231
- Wa i t a Mome n t 232
- Pr int 01/01 232
- Wa i t : 012 232
- F01 HPGL JobNo . 008✽ 232
- 1 Open the cutter door 233
- 2 Open the cutter door 234
- Open the cutter door inside 235
- Wa i t a mome n t 236
- Open the cutter door (⇒Step 1 237
- 4 Cut the end of the paper 238
- Door Open 240
- ■Roll 1 drawer (Door 1) 240
- ■Roll 2 drawer (Door 2) 240
- ■Manual feed drawer (Door 4) 240
- ■Cutter door (Door 5) 240
- ■Top door (Door 6) 241
- ■Fixation door (Door 7) 241
- Scanner Operator Call Errors 242
- ■Cover Open 242
- 1 Open the scanner cover 243
- Operator Call 245
- ■Operator notice warning 246
- WNVRAMERROR 247
- De l e t e Job? 247
- Y=En t e r N=Cance l 247
- WUN-INIT. NVRAM 248
- ■Communication warnings 249
- (2) Mail interface 250
- (3) USB interface 250
- Chapter 14 Troubleshooting 251
- (4) Delivery interface 251
- (5) File (TWAIN) interface 253
- ■PDL warning 254
- (1) Plotter PDL 255
- ■Engine warning 258
- ■Main warning 259
- Service Call Errors 260
- ■Serial number not set 260
- ■Engine error 260
- ■System error 260
- ■Controller errors 261
- Error code Description 263
- 0B80 to 0B8E Program error 263
- F000ot1000rorremargorP 264
- 1001rorresseccaeliF 264
- E 0050-xxxx 265
- Power Of f /On 265
- ■Scanner Errors 266
- Error log 267
- Log Registration Format 268
- Type of Error Log 269
- Warning (Classification: W) 270
- Troubleshooting for ethernet 272
- ■If "MANUAL" is set 274
- ■If "AUTO" is set 274
- When a print error occurs 275
- Appendix 277
- Basic specifications 278
- Menu structure 280
- Appendix-5 281
- ▼ Menu structure 281
- Appendix-6 282
- Appendix-7 283
- Appendix-8 284
- Appendix-9 285
- Appendix-10 286
- MENU MODE 287
- Appendix-12 288
- #PROTOCOL 289
- [RESET] MENU 290
- #SYSTEM RESET 290
- #PORT RESET 290
- >PORT1 290
- Appendix-16 292
- Appendix-17 293
- I I' 294
- Appendix-19 295
- Appendix-20 296
- Appendix-21 297
- Command list 298
- Appendix-24 300
- Appendix-25 301
- ▼ Command list 301
- HP RTL Plotting Command List 302
- Appendix-27 303
- D-SCAN Format Command List 304
- Appendix-29 305
- Appendix-30 306
- Appendix-31 307
- Appendix-32 308
- Appendix-33 309
- TIFF Tag 310
- CALS Format Records 311
- Appendix-36 312
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.431 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern