Seiko 4R36 Bedienungsanleitung PDF herunterladen (Seite 24)

５

Speciﬁ cations

Accuracy of mechanical watches

●

The accuracy of mechanical watches is indicated by the "daily rate."

●

The accuracy of mechanical watches may not fall within the speciﬁ ed

range of time accuracy because loss/gain changes due to the position

of the watch, which is dependent on the conditions of use, such as

the length of time during which the watch is worn on the wrist, arm

movement, and whether the mainspring is wound up fully or not, etc.

● The loss/gain of mechanical watches is not measured by a daily

rate, but by daily rates of one week or so.

●Accuracy variation according to temperature

・

The parts that compose the accuracy of mechanical watches are made

of metals. It is well known that metals expand or contract depending

on temperatures due to metal properties. This exerts an eﬀ ect on the

accuracy of the watches. Mechanical watches tend to lose time at high

temperatures while they tend to gain time at low temperatures.

４

Troubleshooting

Problem Possible cause Solution

The watch stops

operating.

The watch is not wound up

suﬃ ciently.

Turn the crown or swing the watch to wind it up.

The watch will start operating. If the watch not,

consult the retailer from whom the watch was

purchased.

The watch gains/

loses temporarily.

The watch has been left in extremely

high or low temperatures for a long time.

The normal accuracy will resume when the

watch returns to normal temperature.

The watch was brought into

close contact with a magnetic

object.

The normal accuracy will resume when the watch is

kept away from close contact with the magnetic source.

If this condition persists, consult the retailer from whom

the watch was purchased.

You dropped the watch, hit it against

a hard surface or wore it while

playing active sports.

The watch was exposed to strong

vibrations.

The normal accuracy will not resume. Consult

the retailer from whom the watch was purchased.

The watch has not been

overhauled for more than 3 years.

Consult the retailer from whom the watch was

purchased.

The date changes at

12 o'clock noon.

AM/PM is not properly set. Advance the hands by 12 hours.

The glass is blurred and the

blur persists for a long time.

Water got inside the watch due to

the deterioration of the gasket, etc.

Consult the retailer from whom the watch was

purchased.

※

For the solution of troubles other than listed above, contact the retailer from whom the watch was purchased.

３

To preserve the quality of your watch

・

Periodic inspection and adjustment by disassembly and cleaning (overhaul) is

recommended approximately once every 2 to 3 years in order to maintain optimal

performance of the watch for a long time. The power transmission gear of the

movement of this watch constantly receives force. To ensure that this mechanism

works properly all the time, washing parts, changing oil, adjusting accuracy, checking

functions and replacing consumable parts on a regular basis are important. The ﬁ rst

overhaul after the purchase of your watch is particularly important for preserving long-

time use of your watch. According to use conditions, the oil retaining condition of your

watch mechanical parts may deteriorate, abrasion of the parts due to contamination

of oil may advance or delay the time signiﬁ cantly, or the watch itself may stop. As

the parts such as gasket may deteriorate, water-resistant performance may be

impaired due to intrusion of perspiration and moisture. Please contact the retailer

from whom the watch was purchased for inspection and adjustment by disassembly

and cleaning (overhaul). For replacement of parts, please specify "SEIKO GENUINE

PARTS." When asking for inspection and adjustment by disassembly and cleaning

(overhaul), make sure that the gasket and push pin are also replaced with new ones.

When your watch is inspected and adjusted by disassembly and cleaning (overhauled),

the movement of your watch may be replaced.

●

Inspection and adjustment by disassembly and cleaning (overhaul)

３

To preserve the quality of your watch

・ Contact the retailer from whom the watch was purchased or SEIKO

CUSTOMER SERVICE CENTER for repair or overhaul.

・ Within the guarantee period, present the certificate of guarantee to

receive repair services.

・ Guarantee coverage is provided in the certificate of guarantee. Read

carefully and retain it.

・ For repair services after the guarantee period has expired, if the

functions of the watch can be restored by repair work, we will undertake

repair services upon request and payment.

● Notes on guarantee and repair

After-sale service

・ SEIKO makes it a policy to typically keep a stock of replacement parts

for this watch for 7 years. Replacement parts are those which are

essential to maintaining the functional integrity of the watch. Please

keep in mind that if original parts are not available, they may be replaced

with substitutes whose outward appearance may diﬀ er from the originals.

●

Replacement parts

1 2 ... 19 20 21 22 23 24 25

Kommentare zu diesen Handbüchern

Keine Kommentare

Seiko 4R36 Bedienungsanleitung Seite 24

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Seiko 4R36