Seiko DPU-3445 Betriebsanweisung

USER’S GUIDEThermal PrinterDPU-3445-20Read this user’s guide carefully beforeusing the printer.Keep this user’s guide in a place where itcan be access

- 7 -1 PREPARATIONOnce you have opened the carton, make sure it contains the printer and allaccessories.The following are available as options:Keep th

- 8 -2 NAMES OF PARTS(1) POWER buttonThe POWER button turns the printer ONor OFF. To turn the printer on, hold downthe POWER button until the POWERla

- 9 -(7) Paper outletPaper port with a paper cutter. When theplaten cover is closed, paper isdischarged from the top of the printer.(8) Thermal headT

- 10 -3 POWER CONNECTIONThe printer can be powered with a battery pack or an AC adapter.QQQQ Installing a Battery PackThe battery pack should be fully

- 11 -QQQQ Connecting the AC Adapter(1) Connect the AC cable to the AC adapter.(2) Insert the DC jack of the AC adapter to the power connector of the

- 12 -4 PAPER SETTINGThis printer can feed cut sheets and roll paper. The printer function setting for cutsheets is different from that for roll pape

- 13 -QQQQ Setting Roll PaperThis printer can be equipped with an optional paper holder to feed roll paper. Installthe paper holder, then set the pap

- 14 - (6) Turn the printer over again. The ERROR lamp should be lit. Press the FEED button once, and the printer will go into standby mode.HINT• T

- 15 -5 TEST PRINTINGAfter loading paper in the printer, perform test printing. In test printing, the printer'sfunction setting and character st

- 16 -6 FUNCTION SETTINGThis printer allows you to set various function according to operating conditions oruses.The settings are stored in the softwa

DPU-3445-20 THERMAL PRINTER USER’S GUIDEDocument Number U00018388105First Edition May 1999Second Edition January 2000Third Edition April 2000Fourth Ed

- 17 -(4) If the message shown at the right is printed, press the FEED button.[SETTING MODE] Yes: Feed SW / No: Power SWHINT• If

- 18 -DIP switch 2selectionOperation 1DIP switch 1selectionOperation 1DIP switch 3selectionOperation 1Setting completeSetting endselectionOperation 3D

- 19 -Operation 2: DIP switch setting(1) When the message shown at the right is printed, set the bits from the mostsignificant bit (bit 8) to the leas

- 20 -QQQQ Software DIP Switch Setting List: Factory settingsDIP switch 1Posi-tionFunction Setting1 Busy controlbit8Serialcontrol0 Xon/Xoff control1 1

- 21 -DIP switch 2Posi-tionFunction Setting1 Disabledbit8Initial statusautomatictransmission0 Enabled1 JIS codebit7Kanjiencodingsystem0 Shift JIS code

- 22 -7CONNECTING TO THE HOST COMPUTERThis printer supports serial transmission through an interface cable and infraredtransmission. The transmission

- 23 -QQQQ Infrared transmission by IrDA(1) Turn the printer off.(2) Turn the printer on without connecting theinterface cable to it.(3) Place the inf

- 24 -8 RECHARGING THE BATTERY PACKThe battery pack is partially charged prior to shipping, and provides sufficient powerto check the printer operatio

- 25 -QQQQ Recharging with Exclusive Battery Charger(1) Install a battery pack in the charger. Push thebattery pack into the charger and slide it int

- 26 -9 THERMAL HEAD MAINTENANCEThe thermal head of this printer does not require user maintenance.If paper dust accumulates, clean the thermal head t

This equipment has been tested and found to comply with the limits for a Class Bdigital device pursuant to Part 15 of the FCC Rules. These limits are

- 27 -10 TROUBLESHOOTINGCheck the following points before you make a request for repair.QQQQ The power does not turn on. · Is the recommended AC adap

- 28 -11 SPECIFICATIONSQQQQ Printer SpecificationsItem SpecificationPrinting method ThermalCharacters per line 52*1Character size(H × W) Standard size

- 29 -12 OPTIONS AND CONSUMABLE PARTSQQQQ OptionsName ModelPaper holder RH-48-00Battery pack BP-3007-A1AC adapter PW-3009-W2Battery charger BC-3008-W1

Seiko Instruments Inc.8, Nakase 1-chome, Mihama-kuChiba-shi, Chiba 261-8507, JapanPrint System DivisionTelephone:+81-43-211-1219 Facsimile:+81-43-211-

- 1 -INTRODUCTIONUser’s Guide applies to the DPU-3445-20 Thermal Printer.Read through the Safety Precautions on pages 2 to 6 carefully before using th

- 2 -SAFETY PRECAUTIONSThe following symbols are used in this User’s Guide in order to make use of theprinter properly and prevent the printer from be

- 3 -WARNINGDO NOT use an AC adapter or battery pack other than that which isspecified. Doing so may cause fire leading to serious accidents.DO NOT b

- 4 -CAUTIONThis printer is not designed to be dust-proof or water-proof. DO NOTdrop any metallic objects or liquids, such as water or coffee, into t

- 5 -OPERATING PRECAUTIONSPlease follow the precautions below to enjoy and maintain the full performance of theprinter.QQQQ Using the PrinterX Be care

- 6 -QQQQ Thermal Paper HandlingX Store the thermal paper in a cool, dry, and dark place.X Do not rub the paper with hard objects.X Do not leave the p